Skip to content

Our Process

Our process has four gates: read the drawing, choose the workshop, confirm the quote in writing, then follow packing and dispatch. The same person keeps the order.

Our process is deliberately short. A buyer should see who is making the part and which dimension will be checked.

Our process in daily use

EF Manufacturing Solutions is the manufacturing division of a group that began with classic cars in Istanbul. The name on the workshop door has changed. The habit of matching a part to a real vehicle has not.

Fırat Çapalar opened Paşa Galeri in Beyoğlu in 1996. The benches were close to Piyalepaşa. Restorers brought vehicles that needed metal, not a brochure. That is still the test a drawing has to pass.

Paşa Klasik Otomotiv grew up beside the gallery. Panels, small machined pieces and brightwork had to sit correctly on a car people already knew. A near match was not a match.

In 2010 the work moved further into a network of workshops. One bench could not hold every discipline. Welding, machining and paint each needed a specialist who would still answer to the same order.

The group did not buy a factory for every discipline. It kept a short list of workshops it had walked through, and it sent work only where the machine, the people and the inspection habit were already in place.

In 2019 the European company was formed. EF Classic Oldtimer Cars GmbH sits in Duisburg, Arnold Dehnen Str. 45. Buyers inside the EU can contract with a German entity while the part is still made where the discipline is strongest.

The manufacturing desk carries that arrangement into classic and industrial programmes. A restoration shop and a machine builder can use the same counterpart. The drawing decides the route.

Six families of work come up again and again: machining, sheet metal, casting, forging, assembly and surface treatment. A single order can use one of them or run through several before the part is packed.

More than 200 workshops sit in the partner network, across Türkiye and Europe. The figure is not a catalogue to browse. It is the pool used after the geometry, the alloy and the volume are clear.

Fifteen buyer groups show up in the order book, from classic restoration to machinery. The common point is a metal part that has to be traceable back to a drawing and a workshop.

Two continents matter because a buyer in Germany may want a discipline that is mature in Türkiye, and a buyer in Istanbul may want a finish that a European shop already runs every week.

How the group is built

Quality is a written gate, not a slogan. Critical dimensions, material certificates and photos leave the workshop with the part. If a gate fails, the part does not travel on a hopeful email.

Packing and dispatch stay on the same order. The person who accepted the drawing is still the person who confirms the shipment. That is the point of one desk.

The older chapters are told on the group sites. This desk is the chapter that turns a drawing into a delivered part, with the workshop named and the check written down.

A drawing is read for the alloy, the tolerance and the date before any workshop is asked to price it. The commercial note and the technical note leave together.

Repeat work is easier than a first article. The first piece is measured, photographed and compared with the PDF. Only then does a batch make sense.

Classic trim, a machined bush and a cast housing can share one order. They do not have to share one workshop. The desk keeps the sequence.

Certificates are requested when the drawing names a standard. They travel with the part. They are not written after the crate has gone.

Capacity is checked before a promise is made. If the right shop is full, the date moves or another visited shop is asked. An unknown bench is not used to save a week.

Packing follows the part. A polished brightwork piece and a raw casting are not put in the same crate, and the label names the order.

The person who accepted the file is the person who confirms dispatch. Questions after delivery come back to that same name.

Buyers in Europe can contract with the Duisburg company. Buyers who already work with the Istanbul workshops stay on the same manufacturing file.

Related pages: a quote request, the named desks.

EF Classic. Paşa Galeri.

Our process is handled against the drawing, the material callout and the date the buyer actually needs.

People who arrive for Our process still get a named person, not a shared inbox with no owner.

A note about Our process is useful only when the tolerance and the packing method are written down.

The desk treats Our process as a production question: who can hold the tolerance, and who can ship in the agreed week.

Nothing in Our process replaces a visit to the workshop when the part is new or the volume jumps.

Records for Our process stay with the order, from the first PDF to the dispatch note.